Tektronix 1502B TDR Cable Tester
Tests any type paired conductor and coax cable. Max range: 2000ft/500m. Resolution: 12in/30 cm. Matched to 50O cables. Front panel adjust for other impedance’s.

Tektronix 1502C Metallix TDR Cable Tester
Test any type paired conductor and coaxial cable. Maximum range: 2,000ft/625m. Resolution: .05in/l2cm. Matched to 50O cables. Front panel adjusts for other impedance’s. Horizontal accuracy: 1.6 in. or ±1% of measured distance.

Tektronix 1503B TDR Portable Cable Tester
Tests any type paired conductor and coax cable. Max range: 50,000ft/10,000m. Resolution: 1.2in/3.0cm. Selectable 50, 75, 93, or 125O impedance’s.

Tektronix 1503C Metallic Cable Tester
Generates a 1/2 sine pulse with selectable pulse widths of 2, 10, 100 or 1000ns. The high resolution 2ns pulse permits the identification of multiple faults as close together as 1 foot. The 1000ns pulse gives the A range of 5000 to 50,000 feet. (Depending on cable type and condition).

Tektronix 1735 Wave Form Monitor
Complete line select. Simultaneous channel A and B display. VTR servo rates available in NTSC, PAL, or dual standard.

Tektronix 1740A Wave Form/Vector Monitor
Eight video inputs. Wave form and vector displays. Time code wave form display.

Tektronix 1750A Wave Form/Vector Monitor
Eight video inputs. Wave form and vector displays. Time code wave form display. Polar SCH and color framing.

Tektronix 1760 Wave Form/Vector Monitor
Two composite plus two component inputs. Component vector, lighting and diamond displays. Optional SCH and color framing.

Tektronix 1780/81R Video Measurement Set
Full bandwidth analog processing. Precision wave form and vector measurements. Four loop-through video input channels available for either NTSC or PAL standards.

Tektronix 2432A Digital Storage Scope
2 channels. Bandwidth: 300MHz. Sensitivity: 2mV/div. - 5V/div. Sampling rate: 100MS/s. 8 bit. 1k points/wave form. 40MHz single shot. Wave Form extraction. Auto step and set-up. Printer/plotter output. Envelope mode. 2ns glitch capture.

Tektronix 2440 Digital Oscilloscope
4 channels. Bandwidth: 300MHz. 500MS/s digitizing rate, 2 channels simultaneously. 8 bit vert. resolution. 1k points record length per channel. 0.001 5% crystal time base. 2ns glitch capture. Fully programmable and automatic.

Tektronix 2445B Portable Oscilloscope
4 channels. Bandwidth: 150MHz. 2mV/div. deflection factor. Maximum sweep speed 1ns/div.(S/Ns above B06xxx 200MHz bandwidth.)

Tektronix 2465B Portable Analog Oscilloscope
4 channels. Bandwidth: 400MHz. Sens: 5mV/div. at BW. Sweep rate: 500ps/div. CRT readout, delta volts and time meas. Cursors, delayed sweep, auto meas., save features.

Tektronix 2465B-CT -Portable Oscilloscope
4 channels. Bandwidth: 400MHz. Sensitivity: 5mV/div. at BW. Sweep rate: 500ps/div. CRT readout, delta volts and time measurement, cursors, delayed sweep, auto measurement, save features. GPIB. Counter/timer/trigger word recognizer.

Tektronix 2467B Portable Oscilloscope
4 channels. Bandwidth: 400MHz. 2mV/div. deflection fact at BW. Max sweep speed: 500ps/div.

Tektronix 2467BHD High Definition Television Oscilloscope
Built-in counter/timer/trigger (CTT). Auto sets to major TV standards such as 1250/50, 1125/60, 1050/60, NTSC, PAL, SECAM and component systems. Bandwidth: ±3dB at 50MHz.

Tektronix 2712 Spectrum Analyzer
Frequency range: 9kHz to 1.8GHz. Resolution bandwidth 300Hz to 5MHz. Sensitivity up to -127dBm.

Tektronix 2714 Spectrum Analyzer
Designed for cable TV and broadband LAN measurements. Frequency range: 15MHz to 1015MHz. Resolution 0.1dB. Frequency range for spectrum analyzer applications: 9kHz to 1800MHz.

Tektronix 2784 Spectrum Analyzer
Frequency range: 100Hz to 40GHz in coax. Sensitivity: -107dBm at 40GHz.

Tektronix A6302 Current Probe
1mA to 20A, 50A peak. DC to 50MHz.

Tektronix A6303 Current Probe
Current probe for AM 503. 100A AC. Bandwidth: DC - 15MHz.

Tektronix AFG2020 Arbitrary Function Generator
Frequency range: (wine wave) 0.5Hz - 100MHz, (square wave) 0.5Hz - 50MHz; (triangle, ramp and pulse) 0.5Hz - 31.2MHz; resolution: 0.5Hz; max. amplitude: 10V P-P into 50O.

Tektronix ATM150 ATM Analyzer
Operation up to 155MB/s; standard interfaces include DS1/DS3, E1/E3; constant bit rate (CBR) voice and video; variable bit rate (VBR) data mixed traffic profiles; up to four VCI/VPI addresses.

Tektronix AWG2005 Arbitrary Wave Form Generator
20 MS/s clock rate provides up to 10MHz wave forms; standard wave shapes, sine, square, triangle, ramp, noise, arbitrary, linked sequence and DC. Memory: 64k x 12 bits per channel.

Tektronix AWG2021 Arbitrary Wave Form Monitor
250MS/s clock rate provides up to 125MHz wave forms; 256k record length, 12 bit vertical resolution; direct wave form transfers from DSO, built in 1.4MB 3.5 floppy disk, fully programmable from front panel RS-232, or GPIB.

Tektronix AWG2041 Arbitrary Wave Form Generator
Range: 1.024GS/s clock rate provides up to 500MHz wave forms; wave shapes: sine, square, triangle, ramp, pulse, arbitrary, linked sequence, and DC; 1MB record length (4Mb with opt.01). Built in 1.4MB 3.5 floppy disk. Fully programmable. RS-232, or GPIB (IEEE 488.2).

Tektronix CDC250 Universal Counter
Measures Frequency of sine, square, and triangle waves from 1Hz - 175MHz at input levels from 20mV to 42v peak. Also provides period measurements, frequency ration, time interval, and totalize measurement functions.

Tektronix CFC250 Frequency Counter
Frequency range: 5HZ - 100MHz; sensitivity: 5Hz - 30MHz (30nV rms); 30MHz - 70MHz (50mV rms); 70MHz - 100MHz (80mV rms).

Tektronix CFG250 Function Generator
Frequency range: 1 Hz - 1.0MHz, 7 ranges. Amplitude open: 100mV to 20V p-p, 10mV - 2V p-p. Amplitude 50O load: 5OmV - 10V p-p, 5mV - 1V p-p. Wave forms: sine, square, triangle and TTL pulse. Sweep rate: 0.5Hz to 5OHz continuously variable.

Tektronix CFG253 Function Generator
Frequency range: 0.03Hz to 3.0MHz. Amplitude: 0 to 20V p-p (open), 50mV to 10V p-p (Into 50O). Wave forms: sine, square, triangle and TTL. Sweep rate: 0.5Hz to 5OHz continuously variable.

Tektronix CFG280 Function Generator
Frequency range: 0.1 Hz - 11MHz; wave form outputs: square, sine, triangle; TTL pulse; sweep functions for all outputs; output: 0 - 20V p-p.

Tektronix CMC250 Frequency Counter
1.3GHz frequency counter; channel A = 5Hz - 100MHz; channel B = 80MHz 1/3GHz; 50O; display hold; remote start/stop; provides period and totalize measurements.

Tektronix CMC251 1.3GHz Multifunction Counter
Measures frequency of sine, square, and triangle waves from 1Hz - 1.3GHz. Also provides period, totalize, and pulse width measurements. CH. A frequency 1Hz - 100MHz. CH. B frequency 80MHz - 1.3GHz.

Tektronix CSA803A Communication Signal Analyzer
20GHz acquisition and TDR performance. 2.5GHz trigger bandwidth. For high speed digital data communications applications, such as automated eye-diagram analysis, histograms and masks. Uses TEK SD plug-ins.

Tektronix CTS710 SDH/Sonet Test Set
Transmit and receive rates: STS-1, STS-3 (electrical), STS-3c and OC-3c, OC-1, OC-3, OC-12 (Optical), DS1, DS3 (OPT.22). Compliance to ANSI TI-105.

Tektronix CTS750 SDH/Sonet Test Set
Transmit and receive rates: STM-0E, STM-1E (electrical), STM-0, STM-1, STM-4 (optical); 2MB/s, 34MB/s, 140MB/s (Opt. 36). Compliance to ITU-TG. 707, G.708, G.709.

Tektronix SD14 High Impedance Sampling Head
Dual channel, 3GHz probe sampler. 7V p-p dynamic range. Ideal for high speed device characterizations such as ECL, CMOS, ACL, and GaAs testing.

Tektronix SD20 Loop Through Sampling Head
Single channel, 20GHz sampling head designed for low-loss testing such as digital device characterization. Provides acquisition rise time of 17.5ps.

Tektronix SD22 Low Noise Sampling Head
Dual channel, 12.5GHz sampling head specifically designed for low noise measurement in digital communications. provides acquisition rise time of 28ps.

Tektronix SD24 Sampling Head
Dual channel TDR/sampling head. Input impedance: 50O. Rise time 17.5ps with 20GHz equivalent - time BW. Generates two 35ps TDR reflected pulses.

Tektronix SD26 Sampling Head
Same as SD24 but deletes TDR reflected pulses. Used with Tektronix 11801 and 11802 models.

Tektronix SD30 Sampling Head
Single channel, 40GHz sampling head for use in high bandwidth applications. Rise time: less than 8.8ps.

Tektronix SD32 Sampling Head
Single channel, 50GHz sampling head. Rise time: less than 7.0ps.

Tektronix SD42 Optical-To-Electrical Converter
Used to analyze optical signals in the 1000nm to 1700nm wavelength range. Power from 5nW to 5mW can be measured.

Tektronix SD46 Optical-To-Electrical Converter
For use with the CSA803A/11801B. Linear up to 25nW peak input with a calibrated deflection factor from 50µW/div. to 5mW/div at 1300nW.

Tektronix SDBI Trigger Head
Provides stable displays of signals from 1 to 20GHz with less than 6ps rms jitter.

Tektronix SG503 Signal Generator
Frequency range: 250kHz to 250MHz. Three digit LED. Freq. indicator. Output: 5mV to 5.5V p-p into 50O. Must be powered by TM-500 series power supplies.

Tektronix SG5010 Programmable Oscillator
Frequency: 10Hz - 163.8Hz ±.0l %; sine wave, square wave, smpte, ccif offset, and burst; output 21.2V rms into 600O.

Tektronix SG5030 Leveled Sine Wave Generator
Frequency range: 0.lHz to 550MHz. Amplitude range: 4.5mV to 5.5V. Leveling settling time: <20ms. DC offset: +20mV. Internal time base: 10MHz. IEEE-488 standard.

Tektronix SG504 Signal Generator Plug-In
Frequency range: 245MHz-1050MHz ±2%. Output: 0.5V-4.0V p-p into 50O. Amplitude accuracy: 3%. Flatness: 4%. Requires TM500 series mainframe.

Tektronix SJ300E Sonet/SDH Jitter and Wander Analyzer
Complete generation and measurement of phase jitter parameters on Sonet/SDH signals up to 622MB/s. Generates and analyzes line and synchronization signal wander in Sonet/SDH and ATM systems.

Tektronix ST103A SDA/Sonet Analyzer
VT channel scan; multiple sonet alarm generation; J1 trace byte programming; multiple outputs; DCC and order wire access; sonet loop timing.

Tektronix ST112 SDH/Sonet Test Set
A compact single-unit solution for providing extensive sonet STSC-1, OC-1, OC-3, OC-3c, and OC-12 signal generation and analysis for tributary and network testing.

Tektronix ST2400 SDH/Sonet Test Set
2.4GB/s section and line testing for OC-48 and STM-16 (2.4GB/s multiplexer section/regeneration section-Europe). Integrated St112 control Opt. For DS1 through OC-48 sonet testing. Works with CTS750 for E1 to STM-16 SDH testing.

Tektronix TAS220 Portable Oscilloscope
Bandwidth: 20MHz. Dual channel. Main sweep range: 0.5 s/div. to 0.1 ms/div. CRT cursors and readouts. Single time base. Rise time <17.5ns.

Tektronix TAS250 Portable Oscilloscope
Bandwidth: 50MHz. Dual channel. Main sweep range 0.5s/div to 0.1 µs/div. CRT cursors and readouts. Single time base. Rise time <7ns.

Tektronix TDS340 Digital Scope
Bandwidth: 100MHz. Sample rate (each channel): 500MS/s. Time/division range: 5ns to 5s/div. Sensitivity: 2mV to 10V/div. Record length 1000 points.

Tektronix TDS360 Digital Scope
Bandwidth: 200MHz. Sample rate (each channel): 1GS/s. Time/division range: 2.5ns to 5s/div. Sensitivity: 2mV to 10V/div. Record length 1000 points.

Tektronix TDS380 Digital Scope
Bandwidth: 400MHz. Sample rate (each channel): 2GS/s. Time/division range: 2.5ns to 5s/div. Sensitivity: 2mV to 10V/div. Record length 1000 points.

Tektronix TDS410A Digital Scope
2 channels. Bandwidth: 200MHz. Sample rate 100MS/s on all channels. Sensitivity: 1mV to 10V/div.

Tektronix TDS420A Digital Scope
4 channels. Bandwidth: 200MHz. Vertical resolution: 8 bit. Sample rate: 100MS/s (4 CH). Record length: 500 to 5k points. Vertical sens. 1mV-10V/div. Glitch capture: 10ns. Interface: GPIB-IEEE 488.2. Option 1M: 30k points record length. Option 02: Pouch and cover. Option 05: TV trigger.

Tektronix TDS460A Digital Scope
4 channels. Bandwidth: 400MHz. Vertical resolution: 8 bit. Sample rate: 100MS/s (4CH). Record length: 500 to 5k points. Vertical sens: 1mV-10V/div. Glitch capture: 10ns. Interface: GPIB -IEEE 488.2. Option 1M: 30k points record length. Option 02: Pouch and cover. Option 05: TV trigger.

Tektronix TDS520B Digital Scope
Two channel digital scope. Frequency range: DC to 500MHz. Sample rate: 2GS/s. Wave Form acquisition rate: 100,000/s.

Tektronix TDS540B Digital Scope
Four channel digital scope. Frequency range: DC to 500MHz. Sample rate: 2GS/s. Wave Form acquisition rate: 100,000/s.

Tektronix TDS544A Color Digitizing Oscilloscope
4 channels. Bandwidth: 500MHz. Standard features include a full color shutter monitor, 3.5 inch floppy disk drive and RS-232 interface. 1GS sample rate. 50 to 15k point variable record length. Sensitivity: 1 mV to 10V/div. 25 automatic wave form) measurements. Option 1M: 50K record length. Option 2F: Advanced math. Option 05: Video trigger HDTVNTSC, PAL, flex format.

Tektronix TDS620B Digital Oscilloscope
Dual channel. Bandwidth: 500MHz. 2GS/s storage. Vertical deflection: mV/div to 10V/div. Record length: 500-2000 points.

Tektronix TDS640 Digitizing Scope
Four channels. Bandwidth: 500MHz. 1mV-10V sensitivity. 2GS sample rate. 2k points record length. Vertical accuracy: 1.5%. Time base accuracy: 0.01%.

Tektronix TDS644B Digital Scope
4 channels. Bandwidth: 500MHz features include full color display, 3.5 inch, 1.44MB, MS DOS compatible floppy, and RS232/centronics printer port. 1mV to 10V sensitivity. 2.5 GS/s sample rate. Timing accuracy <100ps. 15K record length.

Tektronix TDS680B Digital Scope
2 channels plus 2 auxiliary channels. Bandwidth: 1GHz. Sample rate: 5GS/s. Record length: 15,000 points.

Tektronix TDS684B Digital Scope
4 channels. Bandwidth: 1GHz, 5 GS/s sample rate on four channels. High resolution color monitor, 15K record length, 3.5 inch dos floppy drive, VGA output, 1mV/div. to 10V/div. sensitivity. Timing accuracy: <50ps.

Tektronix TDS724A Digital Scope
Four channel digital scope. Frequency range: DC to 500MHz. Sample rate: 1GS/s. Maximum record length: 250k. Wave Form acquisition rate: 180,000/s. 3.5 inch floppy drive, RS-232/Centronics interface and advanced FFT/math function.

Tektronix TDS744A Digital Scope
4 channel digital scope. Displays over 400,000 acquisitions/s. Sample rate: 1 CH.= 2GS/s, 2 CH = 1GS/s, 4 CH = 500MS/s. Standard memory = 50k.

Tektronix TDS784A Digital Scope
4 channel digital scope. InstaVu* acquisition mode. Sample rate: 1CH. = 4GS/s, 2CH. = 2GS/s; 3,4CH. = 1GS/s. Standard memory = 50k.

Tektronix TDS820 Digitizing Oscilloscope
2 channels. Bandwidth: 6 or 8GHz. Vertical deflection: 2mV/division to 200mV/division. Record length: 500-15k points.

Tektronix TFC200 Optical Power Meter
Spectral range: 750nm to 1700nm; Calibrated wavelengths: 780, 820, 850, 1060, 1300, 1310, 1550nm; Dynamic Range: +10dBm to -70dBm; Accuracy: ±3%.

Tektronix TFP2A Fibermaster Optical Time Domain Reflectometer
2 plug-in module capacity allows dual wavelength operation in Single Mode and multimode without switching modules. Plug-In Optics Module-Single Mode Available FS1300 - 1310nm FS1500 - 1550nm Plug-In Optics Module - Multimode Available FM8500 - 850nm FM1300 - 1300nm

Tektronix TFS2020 Fiber Scout Optical Fault Finder
Simple symbolic display. Fast restoration capability. 4 button operation. Multiple port configurations. High distance accuracy. User configured fault thresholds.

Tektronix TFS3031 Mini OTDR
Five meter, single mode dead zone; 8 meter multimode dead zone; 32dB single mode dynamic range; 28dB multimode dynamic range; 15 to 60dB selectable reflectance threshold; internal memory for 200 wave forms.

Tektronix THS710 Hand Held Digital Scope
2 channels. Bandwidth: 60MHz. Sample rate 250MS/s each channel. 2.5k per channel record length. Time/division: 10ns to 50 s/div. 8ns glitch capture. 3¾ digit DMM with data logger. Performs 21 automatic measurements.

Tektronix THS720 I00MHz Hand Held Digital Scope
2 channels. Bandwidth 100MHz, 500MS/s per channel, 2.5k per channel record length time/div. 5ns to 50s/div; 8ns glitch capture. 3¾ digit DMM with data logger; performs 21 automatic measurements.

Tektronix TLS216 16-Channel Logic Scope
500MGz real-time bandwidth, 2GS/s. Simultaneous sampling across all 16 channels ±100ps timing accuracy across all channels. Time qualified triggering with four 16-bit word recognizers. Includes 3.5” 1.44MB floppy drive.

Tektronix TM502A Mainframe
Power module mainframe for up to two TM series modules.

Tektronix TM503B Mainframe
Power module mainframe for up to three TM series modules.

Tektronix TM506A Mainframe
Power module mainframe for up to six TM series modules.

Tektronix TM5000 Series Mainframe
Provides power for interconnecting test and measurement plug- in instruments. Accepts 5000 series programmable instruments, 4041 instrument controller and manual TM500 plug-ins. Various plug-ins are listed under generic headings throughout this catalog.

Tektronix TM5003 Mainframe
Accepts 3 TM5000 Series Plug-Ins.

Tektronix TM5006A Mainframe
Accepts 6 TM5000 Series Plug-Ins.

Tektronix TR503 Tracking Generator
Used with all 2750 and 490 series spectrum analyzers. Frequency range: 100kHz to 1.8GHz. Output level 0dBm +0.5dB. Range 0-59dB in 10dB and 1dB steps. Dynamic range 110dB.

Tektronix TS100 Telephone Cable Tester/Fault Locator
½ Sine, balanced signal; 20V into 100O amplitude. 100O output impedance; 20-3000ns pulse widths; 45,000 FT range depending on cable length user selectable filter. 0-6dB gain. Stores up to 20 wave forms with notes.

Tektronix TV110 TDR Cable Tester for CATV.
Designed specifically for CATV/Coaxial cable applications. Dedicated 75O F-connector. Pulse widths optimized for CATV/Coaxial cable runs. Return loss measurement. Simple wave forms, cable types and UPS stored in memory.

Tektronix VM100 Video Measurement Set
Automatically measures 12 key NTSC video parameters. Average modes for accurate results in low signal to noise.

Tektronix VM700A Video Measurement Set
Displays numeric values or graphic displays. The auto mode makes standard video measurements automatically, including those specified in RS-250B/E1A-250C, NTC-7 and RS-170A - for NTSC measurements. CC1R Rec. 624.-1, Rec. 567, and Rec. 569 - for PAL measurements. Opt. 01: - NTSC measurements. Opt. 11: - PAL measurements.