Hioki 3169-20 Power Quality Analyzer

No stress rentals! We help you to choose the equipment that you need, we expedite shipment, and follow up to make sure that your testing is going smoothly!

Hioki 3169-20 Power Quality Analyzer
  • Features & specifications

  • Single-phase to three-phase 4-wire circuits with a single unit
  • Voltage, current, power, power factor, and integrated values
  • Simultaneously perform demand and harmonic measurements
  • Fast enough to measure the power of just a few cycles
  • RS-232C interface for PC communications
  • Includes PC card for data storage
  • Available for Rent and for sale (Used)

Basic Specifications
Measurement line type Single-phase 2-wire, single-phase 3-wire, three-phase 3-wire, and three-phase 4-wire systems (50/60 Hz)
Number of systems that can be measured (for systems that share the same voltage) 1P2W - 4 systems
1P3W - 2 systems
3P3W2M - 2 systems
3P3W3M - 1 system
3P4W - 1 system
3P4W4I - 1 system
Parameters Voltage, current, active power, reactive power, apparent power, power factor, integrated value, frequency, and harmonics.
Measurement method Simultaneous digital sampling of voltage and current, PLL synchronization or a fixed clock (50/60 Hz)
Input methods Isolated voltage input and isolated current input using a clamp-on sensor
Display 5.7 in. backlit LCD (320 x 240 dots.)
Input resistance Voltage: 2.0 MΩ ± 10% (differential input)
Current: 200kΩ ± 10%
Maximum input Voltage input: 780 Vrms AC, peak value: 1103V
Current input: 1.7 Vrms AC, peak value: 2.4 V

Measurement Specifications
Measurement method
(Voltage & Current)
True RMS method
Measurement display
(Voltage & Current)
Measurement of 3 voltage lines and 3 or 4 current lines is possible when using 3-phase 3 wire and 3-phase 4-wire systems.
Measurement display
(Active power)
For three-phase 3-wire (the 3P3W3M setting), refer to the display for phase power values
Polarity display
(Active power)
For consumption: no signal for regeneration
Reactive Power measurement ON: Measures the reactive power directly using the reactive power measurement method
OFF: Calculates the reactive power from the measured values of voltage, current, and active power
Polarity display For lag phase (LAG: current is slower than voltage)
For lead phase (LEAD: current is faster than voltage)
(Reactive power measurement: ON)
Polatity display
Apparent power
No polarity
Measurement range
(Power factor measurement)
-1.0000 (lead) to 0.0000 to + 1.0000 (lag)
Polarity display
(Power factor measurement)
No polarity
Measurement range
(Frequency)
40.000 to 70.000 Hz
Input area for guaranteed accuracy Within 10 to 110% of the range (for sine wave input)

General Specifications
Operating environment Indoors, up to 2000m above sea level
Operating temperature 0 to 40°C, 80% RH or less (non-condensing)
Storage temperature -10 to 50°C, 80% RH or less (non-condensing)
Withstand voltage
(50/60 Hz for 15 sec.)
5.55 kVrms AC between the voltage input terminal and the instrument casing
3.32 kVrms AC between the voltage input terminal and the current input terminal/external interface terminal
2.3 kVrms AC between the Power Supply and the instrument casing
1.39 kVrms AC between the power supply and the current input terminal/external input terminal
Power supply voltage rating 100 to 240 V AC, 50/60 Hz
Maximum rated power 30 VA
Dimensions & weight (W x H x D), (210 x 160 x 60)mm, 1.2 kg
Standard accessories Quick Start Guide
Documentation CD
Manual for PQA-HiViewpro
PQA-HiView Pro CD
Battery Pack
Power Cord
Hard Carrying Case
Meter LAN Crossover Cable
Model 9661: 500 amp CTs, qty. 4
4 Leads: (Yellow, Red, Blue, and Black)
Compact Flash Adapter
32 MB (or greater) Compact Flash Memory Card
12 Volt AC Adapter
400Hz Measurement Function Manual
Mode Instruction Manual
Multi Card Reader with USB Cable