Anritsu ME - 462B DS - 3 BERT Test Set
Allows end to end or loop back testing of DS-3 circuits. Simultaneously measures bit errors, parity errors, and bipolar violations.

Anritsu ME - 522A BERT Test Set
Freq. range: 1MHz. Measures error rate and performs analysis. Built-in printer and GPIB are standard.

HP J2300A WAN Protocol Analyzer
64Kbps WAN Analyzer equivalent to an HP 4957A. Housed in a ruggedized case with 486 DX4 PC with 256MB disk and 4MB of PC memory.

HP J2301B T1 Internet Advisor
Full range 2MBps analyzer with color display. Integrates all your testing requirements such as WAN, LAN, ATM, IDN, and analog TIMS.

HP J2302B E1 Internet Advisor
Full range 2MBps analyzer with color display. Built-in 486DX4, 100MHz processor, 16MB PC memory. 256MB hard drive standard, 512 MB optional.

HP J2306B Ethernet Under Cradle
For Internet Advisor. Under cradle used with HP J2301B or J2302B.

HP J2309B Ethernet/Token-Ring Under Cradle
Under cradle used with J2301B or J2302B.

HP J2522B Ethernet Advisor - LAN
Housed in a ruggedized case with a 486DX4 PC with a 256MB disks and 4MB of PC memory.

HP J2523B Ethernet/Token Ring Internet Advisor
Housed in a ruggedized case with a 486DX4 PC with a 256MB disks and 4MB of PC memory.

HP J2524A FDDI Under Cradle
FDDI under cradle with 32 MB buffer memory. Used with J2522A/B, J2523A/B J2302A/B.

HP J2527A TIMS Under Cradle
Available with opt. 001-TU-T solution with 820/1020Hz tone.

HP J2909A Slide-In Module
ATM DS3 slide-in module and ATM advisor software for HP J2301B or HP J2302B.

HP J2910A Slide-In Module
ATM CEPT-E3 slide-in module and ATM advisor software for HP J2301B or HP J2302B.

HP J2915A ATM Advisor Software
ATM advisor software. T1/E1 analysis.

HP J2916A DS3 Under Cradle
Includes ATM advisor software.

HP J2917A CEPT-E3 Under Cradle
Includes ATM advisor software.

HP 3764A Digital Transmission Analyzer
Error and jitter measurements at 140MB/s or error measurements at 704kB/s, 2,8,34 and 140MB/s. Internal synthesizer for measurements from 1kB/s to 170MB/s at binary interfaces.

HP 3770B T1 Tester
Complete range of T1 installation and maintenance measurements in one tester. Fractional T1 bert and configuration measurements. Error performance based on BPVS, logic, frame, and pattern errors. Frequency, pattern slips, simplex current, level round trip delay, pulse shape clock slips, channel mapping and channel VP output.

HP 37702A Digital Data Tester
Performs full range of DDS testing from simple in-service tests to complete installation and acceptance tests. Built-in T1 channel access allows access to a signal in any time slot.

HP 37704A Sonet Test Set
Provides a wide range of test for verifying sonet equipment such as line systems, add drop multiplexers, digital cross connects, and line-terminals multiplexers.

HP 37714B/C PDH/SDH/ATM Modular Transmission Test Sets
PDH rates of 704Kb/s and 2,8,34 and 140MB/s are provided. SDH module operates at 155 and 622MB/s with a range of optical interfaces at 1310 and 1550nm. ATM cell module gives transmit and receive capability at the physical and cell layers. HP 37714C has a color display.

HP 37721A Digital Transmission Analyzer
Bit and code error testing at 704kB/s, 2,8,34 and 140MB/s. Text and graphic results on large display. Stored setups and auto setup. Remote control. Freq. offset & measurement. Multiple outputs.

HP 37722A Digital Telecom Analyzer
Complete range or in-and out-of-service telecom installation and maintenance measurements. Measures bit errors, code errors, frame errors, CRC errors, rebes (E Bits), slips, round trip delay.

HP 37724A SDH/PDH Test Set
SDH testing at 155MB/s (STM-1) and 6122MB/s (STM-4) PDH testing at 2MB/s and 140MB/s. Comprehensive field portable test set.

HP 37732A Telecom/Datacom Analyzer
Consists of the HP 37722A and the HP 15901A option 001 datacom module. SDH/PHD test sets. Provides testing for V.24, V.35, V.11/X.21 lease interfaces at rates up to 2MB/s. BER/Fler testing. Built in V.24 breakout.

HP 37741A DSI Tester
Hand held T1 Test set with all the features normally found in larger instruments. Provides full T1 and fractional T1 transmit and receive capabilities and is compatible with all from formats.

HP 37742A 2M Test Set
Hand held 2MB/s test set. Provides full 2MB/s transmission and reception, compatibility with CRC 4 frame formats.

HP 37744A Sonet Tester
Frame formats: STS-1 and STS-3. Test Interfaces: Optical 51, 84MC/s and 155MB/s (13nm). Coded Electrical: 51.84 (B3ZS) and 155.52 (CMI) MB/s.

HP 3784A Digital Transmission Analyzer
G.821 error analysis at 704kb/s, 2,8 and 34MB/s. Optional jitter generation and measurement at 2,8 and 34MB/s. Clock synthesizer for rates between 1kb/s and 50MB/s. Optional V.11 interfaces for testing X.21 leased circuits.

HP 37900D Signaling Test Set
Multilink tester for SS No. 7 network signaling text decoding of level 2,3 and 4 messages. Automatic tracing of SS No. 7, ISDN, and mobile messaging sequences.

HP 4934A Transmission Impairment Set
Frequency rate up to 110kHz. Noise to noise ground., noise with tone, and signal to noise ratio. 3 level impulse noise.

HP4957A Protocol Analyzer
64Kb/s performance for quickly isolating problems during the installation, maintenance, and design of data communication networks and equip. Built in RS-232C, RS449, and V.35 interfaces. 768kb extended capture buffer. LCN and called/calling address filter efficiently locates problems in X.25 networks.

HP 59401A Bus System Analyzer
Especially designed to monitor HP-IB (IEEE 488) bus systems. Monitors all bus lines. Represents data lines, any memory location, or DIO front panel switch setting; in octal code and ASCII character. Stores up to 32 characters of bus traffic.

HP 83480D Digital Communications Analyzer
Executes SDH/SONET and Fiber channel eye-diagram tests with efficient self- aligning and self-scaling masks that adjust to the displayed wave form.

HP 83483A Two-Channel Module
Provides two channels with user-selectable bandwidths.

HP 8920A Communications Test Set
Frequency range: 250kHz-1GHz. Audio generator: DC-25kHz, RF frequency measurement range: 460Hz-1GHz. AF frequency measurement range: 20Hz-400Hz. O-Scope Bandwidth (3dB) 2Hz-50kHz. Tests cellular phones, land mobile radios and communication systems.

IFR 1200S Communications Monitor with Spectrum Analyzer
Freq. Range: 250kHz to 1GHz. AM/FM generator, scanning receiver with built-in spectrum analyzer. Includes microphone, telescoping antenna, audio voltmeter and DTMF decode. Opt. 02: Simulcast paging & 0.05 PPM oven oscillator. Opt. 04: Battery pack. Opt. 12: Tracking generator.

IFR 1500 Communications Monitor With Spectrum Analyzer
Freq. Range: 1MHz to 1GHz. AM/FM signal generator to 1GHz. Cable fault locator. Sweep generator. RF frequency and RF power meters. Deviation/modulation meter (10 to 20Hz).

Sage 930A Communication Test Set
High performance TMS and return loss measuring set with built-in DP, MF and DTMF sender. Meets or exceeds the applicable portions of AT&T pub. 41009. Additional options available.

Tektronix ATM150 ATM Analyzer
Operation up to 155MB/s; standard interfaces include DS1/DS3, E1/E3; constant bit rate (CBR) voice and video; variable bit rate (VBR) data mixed traffic profiles; up to four VCI/VPI addresses.

Tektronix CTS710 SDH/Sonet Test Set
Transmit and receive rates: STS-1, STS-3 (electrical), STS-3c and OC-3c, OC-1, OC-3, OC-12 (Optical), DS1, DS3 (OPT.22). Compliance to ANSI TI-105.

Tektronix CTS750 SDH/Sonet Test Set
Transmit and receive rates: STM-0E, STM-1E (electrical), STM-0, STM-1, STM-4 (optical); 2MB/s, 34MB/s, 140MB/s (Opt. 36). Compliance to ITU-TG. 707, G.708, G.709.

Tektronix SJ300E Sonet/SDH Jitter and Wander Analyzer
Complete generation and measurement of phase jitter parameters on Sonet/SDH signals up to 622MB/s. Generates and analyzes line and synchronization signal wander in Sonet/SDH and ATM systems.

Tektronix ST103A SDA/Sonet Analyzer
VT channel scan; multiple sonet alarm generation; J1 trace byte programming; multiple outputs; DCC and order wire access; sonet loop timing.

Tektronix ST112 SDH/Sonet Test Set
A compact single-unit solution for providing extensive sonet STSC-1, OC-1, OC-3, OC-3c, and OC-12 signal generation and analysis for tributary and network testing.

Tektronix ST2400 SDH/Sonet Test Set
2.4GB/s section and line testing for OC-48 and STM-16 (2.4GB/s multiplexer section/regeneration section-Europe). Integrated St112 control Opt. For DS1 through OC-48 sonet testing. Works with CTS750 for E1 to STM-16 SDH testing.

TTC Intercepter 1402S Communications Analyzer
Offers monitoring and testing at 2,8,34 and 140MB/s in a single instrument. Provides analysis and stress testing of DSH and PDH networks and equipment. Multiplex and de-multiplex between rates to test your network from one access point. Measurements: bit errors, FAS errors, G.821 and M.2100 performance, round trip delay, alarm detection.

TTC NL3000 Enterprise Network Analyzer
Intel 80386SX, 20MHz. Intel processor with 2MB RAM, MS-DOS, 60MB hard drive, 3.5 ins. floppy drive, keyboard, 1MB capture buffer and hard disk storage to 16MB. Interfaces: RS232/V.24, RS-449/V.36, V.35, X.21.

TTC T-Berd 209A T-Carrier Analyzer
Offers T1 testing in a portable platform. Provides pulse shape, auto configure, TDR, FT1, CSU/NU emulation, G.821 performance, battery option, full duplex channel monitor with channel insert.

TTC T-Berd 209-OSP Fireberd Carrier Analyzer
T1 Test set focused at ‘Outside Plant’ (OSP) testing. Includes HDSL cable; qualification feature: DC volt, AMP and ohmmeter; TDR. Complete stress pattern testing, automated test sequence.

TTC T-Bert 211 T-Carrier Analyzer
Similar to T-Berd 209A tester, but offers wide band and high band jitter measurements and optional spectral analysis.

TTC T-Bert 224 PCM Analyzer
Full-duplex, T1 channel access test set with call ID option. Signaling option scans all 24 channels for signaling activity and digit analysis. Bit error rate testing option to test T1, fractional T1 and DDS circuits. VF testing option to qualify voice freq. circuits. DSU-DP option to connect protocol analyzers, data scopes, and external DTE to a T1 circuit. Enhanced ESF/SLC option to decode and display the SLC-96 and ESF derived data links.

TTC T-Berd 310 SONET/ATM/DS3/DS1/DS0 Communications Analyzer
Full SONET, ATM (OC-3c and DS3), DS1/0 and fiber optic testing capabilities. Automate test routines with LabVIEW. Advanced remote control and printout capability. Offers DS1/DS0 analyzer, E1 Drop, DS1 Insert, DS3 Jitter, G.821 performance, OC-12 transmit and receive, SONET STS-1 transmit and receive.

TTC 30678 DDS DSO/AB Interface
Analyzes DDS subrate circuits with DSOA, DSOB and clear channel compatibility for all data rates.

TTC 4000 Communications Analyzer
Operates at rates of 50b/s to 15MB/s for testing digital communications circuits. Opt. 001: Second Interface Slot Opt. 002: IEEE-488 Remote Control/Printer Interface. Opt. 004: G.821 Performance Analysis Opt. 005: Freq. Synthesizer Opt. 006: Used Defined Sync Patterns

TTC 40014 RS-449/422 Interface
RS-449 (RS-422/V11) interface to work with TTC 1020B.

TTC 40200 DTC/DCE Interface
RS-449 (422/423) DTE/DCE interface used with Fireberd error analysis series. Can be used with TTC4000 and 6000 analyzers.

TTC 40202 V.35/306 DTE/DCE Interface
CCITT V.35 & Bell PUB41304 & 41450. DTE & DCE emulation. Compatible with all Fireberd units.

TTC 40204 Interface
Interface for TTC 6000.

TTC 40298 Interface
MIL STD 188-114 Interface for TTC6000.

TTC 40540 DS1/T1/D4/ESP/SLC-96 Interface
Interface for testing DS1/T1/D4/ESF/SLC-96 Compatible with Fireberd MC6000 series.

TTC 40606 15-Pin D to 8-Pin Modular RF 48
15 pin D to 8 pin modular RF 48 (10’). For use with TTC 209A and 211 only.

TTC 41075 Interface
Interface used with TTC 6000 Fireberds.

TTC 41121B Data Interface
DDS local loop interface for use with the 4000 and 6000A series Fireberd communications analyzers.

TTC 4113B DDS Local Loop Interface
Test DDS four-wire facilities to CPE. Emulates DSU/CSU at all data rates.

TTC 41400 RS-449/530/MIL Interface
Tests RS-449.

TTC 41440A T1/FT1 Drop & Insert Interface
Test NX64 Kb/s or NX56 Kb/s fractional T1 to full bandwidth T1 at 1.544MB/s. Supports drop and insert, V.54 loop codes, and jitter testing.

TTC 41800 CCITT 2.048M/NX64 Kb/s Drip & Insert Interface
Performs NX 64Kb/s or NX56 Kb/s analysis from 2MB/s circuit access point.

TTC 41945 DS3 Transmission Test Interface
Tests 45MB/s circuits and equipment.

TTC 42219 HSSI DTE Interface
Operates at rates up to STS-1 (52MB/s) allowing Fireberd to test HSSI-complaint equipment.

TTC 42242 Diphase Interface
Receive and transmit modulated and conditioned Diphase signals allowing Fireberd to test Diphase multiplexers and communications links.

TTC 42522 V.35/306/RS-449/X.21 DTE/DCE Interface
Operates at rates to 15MB/s. Allows Fireberd to replace any V.35, RS-449 or X.21 devise. Supports end-to-end and loop back testing.

TTC 43400 DS1/DS3 ATM
Tests at the ATM layer, transmission convergence (TC) sublayers, and ATM adaption layer (AAL). Verify all aspects of ATM connection. Perform end-to-end testing with test cell generator and traffic shaping.

TTC 500C Internetwork Analyzer M.F.
33MHz; 80486 processor; MS-Windows, MS-DOS, 16MB RAM, 127MB hard disk and 3.5 in. 1.44 floppy.

TTC 6000A Fireberd Communications Analyzer
Operates from 50b/s to 52MB/s with error measurement and analysis capabilities. Built-in frequency synthesizer, G.821 performance analysis, delay measurements, clock recovery and timing analysis. Automate test routines with LabVIEW. Advance remote control and printout capability. T1 and E1 jitter. Opt. 6001: DS1 wideband jitter measurement. Opt. 6002: DS1 jitter spectral analysis. Opt. 6003: DS1 jitter generation. Opt. 6010: Frame Relay.

Request a Quotation
Back to list of Categories